? *
Short command list:
? 1: <none> 2: <command> 3: <'*'>
   Display list of available command & general help (1) or help for a given command (2) or a detailed list of all commands (3)
adreset <+|->
   Switch stereo or mic board A/D reset line on or off.
aes 
   Select AES/EBU for audio input.
aesi 
   Display info about AES/EBU receiver and transmitter chips.
aesout [<32|44|48|sync|aesin|codec> <32|44|48|sync|in> <sec delay>]
   Toggle AES output sync mode forth an back between given modes. Without parameter the task is stopped.
aesr [<'t'|'r'> <reg0..127> [count]]
   Get one or more values from subsequent registers of tranmit/receive AES/EBU chip. With no parameter given important registers of both chips will be displayed.
aessrc [int|32|44|48|rcv|sync]
   Select or display AES/EBU output sample rate: 'int' uses the system sample rate and no sample rate conversion is applied, '48' converts to 48kHz, '44' to 44.1kHz, '32' to 32 kHz and 'rcv' to the sample rate of the AES/EBU receiver.
aesw <'t'|'r'> <reg0..127> <val0..255> [<val>...]
   Write values to subsequent register of transmitter/receiver AES/EBU chip.
analog 
   Select analog inputs as audio source.
ancill <+|->
   Switch on/off ancillary data transmission and receiption.
app 
   Query cgi communication server.
atdt [<esc-char>|nobreak]
   Enter or quit transparent RS232 ancillary data mode. To return to normal console mode enter '+++' respectively the optionally specified ESC character after a guard time of 1 second. You can specify 'nobreak' as a parameter in which case it will not be possible to escape from the transparent mode other than thru a telnet session or by rebooting the unit.
audioin [analog|aes|livewire]
   Select audio input interface. 'aes' is only available on the studio unit.
autodial [<index0..99> [<name> <number1|-> <z|v> <number2|-> <z|v|m> [codec|custom]]] or <index0..99> <erase!> or <index0..99> !

If [custom], supply <enco> <deco> <bitrate> <samplerate> [<L3-compatibility>] as per other commands
   Store autodial setup. The 'name' must not contain any spaces. Underscores will be converted to spaces. Enter a dash for the phone number if no call should be made. 'z' specifies a Zephyr-type call, 'v' a voice call, 'm' a modem call. 'codec' stores the codec settings along with the setup. If no parameter is specified all setups will be displayed. If 'erase!' is specified with a setup index it is erased. If the exclamation mark is specified the autodial is activated. If only 'index' is specified this setup will be displayed.
automodem [+|-]
   Enable/disable 'auto-modem' feature. When enabled an incoming G.711 (POTS) call will automatically change the network mode from ISDN to ISDNmodem and vice versa for incoming ISDN data calls.
autoredial [<delay (secs)|0>]
   Enable or disable the ISDN auto-redial feature. Maximum delay is 20 seconds, 0=off.
backlight <0..0x7F>
   Select the frontpanel LCD screen backlight.
bitrate <56|64>
   Choose bitrate per ISDN channel (in kbps).
bootstat [clear]
   See the status of the last boot
buttonlock <+|->
   Enables/disables frontpanel mixer button locking.
bye 
   Log off from the command interpreter.
checker [<+|-|on|off>]
   Enable or disable the checker task.
contrast <0..0x7F>
   Select the frontpanel LCD screen contrast.
country [<country>|'list']
   Specify country name for analog modem calls, show current country or display a list of country names.
ddsovr [offset Hz]
   Set the DDS frequency to 12.288 MHz + offset. This will also disabled the streaming tracker. If no parameter is specified the tracker is turned on again.
ddswin <window size>
   .
dec [ancr|init|r|rlc|w <offset> <value>]
   Display decoder status info or read ancillary (ancr) data or re-initialize access pointers (init) or read config table (r) or reset lost lock counter (rlc) or write value to table offset.
decomode <Auto|G722|L2M64|L2|L3D/M|L3|AAC64|AAC|AACLDM64|AACLD>
   Choose decoding algorithm.
delay <msec>
   Delay for the given amount of milli-seconds. Useful for batch commands.
dload < <dsp# 0..3> <filename> >
   Load DSP with binary code from a file and initialize.
dmr 1: <'0'..'3'> <addr> [lines] 2: <none>
   Read data from given DSP 0..3 memory address (1) or continue reading from previous address (2). To access memory bank X add 0x1000000 to the address. For Y add 0x2000000. DSP-4 is located on the mic board.
dmw 1: <'0'..'4'> <addr> <value> 2: <value0..0xFFFFFF>
   Write a 24-bit value to given DSP 0..3 memory address (1) or continue writing to increasing addresses (2). To access memory bank X add 0x1000000 to the address. For Y add 0x2000000. DSP-4 is located on the mic board.
dsp <0..4>
   Reset the given DSP thru host port vector 0.
dtmf <numbers|+|->
   Send DTMF tones to far end of a POTS connection or enable/disable DTMF tone transmission.
enc [<br|sr|ds|cm|sm|bw|crc|r|w|err|init> <value>]
   Display or set encoder settings. Commands affect: bitrate, sample rate down-sampling, channel mode, stereo mode, bandwidth, crc. Channel modes are: stereo, joint, dual, mono, monol, monor, double. Stereo modes are: none, is, ms, isms. CRC can be 0 or 1. Command 'r' reads the config table, 'w' writes a value to a given offset 'err' prints out the error info in P-memory, 'init' re-initializes host table pointers.
encomode <L3dual|L3mono128|L3joint|L3stereo|L2half64|L2mono64|L2mono128|L2joint|L2stereo|G722|AACmono64|AACmono128|AACjoint|AACstereo|AACjoint64|AACLDmono64|AACLDmono128|AACLDjoint|AACLDstereo>
   Choose encoding algorithm.
exit 
   Log off from the command interpreter.
ffs ['compress' | <file number> | 'erase' <file number> [file number] | <file number> <file name>]
   With no parameter specified this prints out detailled file system info. With 'compress' specified the flash contents are read to RAM, the flash is erased and reprogrammed. With a file number given the contents of the file is displayed. With 'erase' the specified file is erased. With a file name the specified file is read from the Linux filesystem and written to the flash using the given file number.
fpdump [<filename>]
   Dump out the contents of the currently visible frontpanel screen. Otherwise, the decoded .BMP data is stored in the file.
fpga 
   Display detailled FPGA settings.
fptest 
   Turns on all frontpanel LED and blackens LCD screen. Check keys and knobs of a new frontpanel. For each key press and key release a click sound is played. Knobs must be turned all the way to the ends to trigger the click. Pressing the same key twice in a row aborts the command. 
heapi 
   Display heap usage information.
help 1: <none> 2: <command> 3: <'*'>
   Display list of available command & general help (1) or help for a given command (2) or a detailed list of all commands (3)
hpvol <0..$3F>
   Set headphone volume.
info 
   Display various information on the hardware settings.
ingain [<-12...12>]
   Set input gain (in dB) for the stereo audio board.
intinfo 
   Display infos from Linux interrupt handler.
ipaddr [<IP-address>]
   Enter IP address or display current addresses. IP number must be given decimal, ie. 192.168.0.5.
ipdns [<dns-server-IP>]
   Enter DNS server IP address or display current addresses. Decimal format is tried first.
ipgate [<gateway-IP>]
   Enter gateway IP address or display current addresses. Decimal format is tried first.
ipmac [<HW address>]
   Enter 6-digit unique MAC. Telos prefix will be prepended. 

Example: 00000F results in MAC of 58:50:AB:00:00:0F
ipmask [<IP-mask>]
   Enter IP mask or display current addresses. Decimal format is tried first.
ipresolv <hostname>
   Resolve the host name to an IP address.
ipstreamttl [TTL value]
   Specify TTL value for streaming sockets (def=5).
isdnaccept <line0/1>
   Accept incoming call on given line.
isdnautoans [off|phone|ISDN|all]
   Select or display ISDN autoanswer mode.
isdncall <line0/1> <number> <data|voice|modem>
   Make outgoing call on given line.
isdndisc [<line0/1>]
   Disconnect call on given line. If no line is specified all calls will be disconnected.
isdndn 
   <line0/1> <number|->
isdnerrs 
   Dumps ISDN error stats
isdni [N|T]
   Display status information of all lines. If option N is specified this will print all SPID and DN/MSN numbers. Option T displays call times.
isdnmsn 
   <line0/1> <number|->
isdnspid <line0/1> <number|->
   Set or delete SPID number.
isdntelco <5ESS|DMS100|NI1|Net3|Ins64>
   Select ISDN telco type. Unit must be reset in order for the change to take effect.
isdntest 
   Performs pattern tests to detect read/write errors on peripheral data bus
l3compat [zephyr|slimline]
   Select compatibility mode for L3 encoder and decoder: For normal operation set to 'zephyr'. To talk to a Dialog4 Slimline set to 'slimline'.
levelin [cons|prof]
   Select consumer or professional level for analog inputs.
levelout [cons|prof]
   Select consumer or professional level for analog outputs.
levinfo <channel 0..3>
   Read level info for mixer <channel>
linequality [<0..10>]
   Select the desired minimum line quality for analog modem connections (0=default).
linestatus 
   Display ISDN or V.35 line status.
loadset 
   Display CRC32 of important DSP and FPGA files.
location [<number0..29> [<name> [audio]]] -or- <number0..29> ! -or- <number0..29> erase!
   Store the current configuration as a location setup. If 'audio' is sepecified the current audio settings will be stored along with the setup. If no parameter is specified all location setups will be listed. If the exclamation mark is specified the location setup is activated. With 'erase!' it will be deleted.
log [<dbg|ext|isdn|il2|il3|iie|istk|sip|off>]
   Add a combination of logging channels or turn off logging.
login <password> [<new password>]
   Log into the command interpreter or change password. Use '-' to substitute for an empty password when changing.
logoff 
   Log off from the command interpreter.
logon <password> [<new password>]
   Log into the command interpreter or change password. Use '-' to substitute for an empty password when changing.
logout 
   Log off from the command interpreter.
loop [<isdn|v35|mpeg|amother|off>]
   Turn on various loop modes or disable all loop modes.
memi 
   Display memory usage overview.
mf <addr> <byte> <count>
   Fill CPU memory with a byte value.
micassign [<mic1..4> <L|R|B|->]
   Assign the specified microphone input to the left, right, to both or no input channel.
micdsp 
   Print info on mixer-DSP settings.
micgain [<<mic1..4>|A> <linepro|linecons|mic+30|mic+44>]
   Set mic board input sensitivity. If the microphone index is 'A' all inputs will be set to the given gain.
miclowcut [<mic1..4> <+|->]
   Switch on/off the lowcut filter for the specified microphone input channel.
micpan [<mic1..4> <-10...+10>]
   Set the panning for the specified microphone input in case it is assigned to both input channels. -10 pans to the left, 10 pans to the right, 0 pans to the center.
micphant [<+/->]
   Turn phantom power for mic inputs on or off or display settings.
micprocess [<mic1..4> <VoiceL|VoiceM|VoiceH|Music|Off>]
   Select the processing type for the specified microphone input.
modem [reset|aansw|log <mode0..7>|info|route <riser|normal>|maxbr <max-bitrate>|qbs <buffer-size>|offhook|onhook|dtmf <number>|dial <number><word1> [<word2>]...]
   Data can be written as a message by spcifying a number of 24-bit words. 'aansw' goes offhook and answers a call in analog mode. 'reset' resets the V.34 modem. 'info' displays status information. 'route' can be used to connect the modem software to the Riser Card (riser) instead of the ISDN line (normal). This will also reload DSP-2 with the proper modem DSP code (either analog or ISDN Modem software). 'maxbr' can be used to restrict the connection speed to a given baudrate. 'q' query quality level. 'bs' can be used to override the automatically calculated transmit buffer size. 'offhook' put the analog line offhook. 'onhook' put the analog line onhook. 'dtmf' DTMF-dials a given number thru the analog modem software. 'dial' performs offhook operation and DTMF dials given number. When no parameter is given the 'StatusRequest' command will be issued to the DSP.The modem DSP code 'modem' and/or the AAC mono encoder and decoder will be loaded if not yet present! Make sure the 'modem' loadset code is the correct ISDN or analog modem code binary!
moniassign [<monitor1/2> <S|R|B|->]
   Switch selected monitor to send audio, receive audio or both send and receive or off.
monibalance [<monitor1/2> <-10...10>]
   Select balance between send and receive audio. -10 enables send audio only, 10 enables receive audio only. Applies only if both send and receive are enabled for this monitor.
monimix [<monitor1/2> <snd|rcv> <L|R|M|S>]
   Select source channel for either send or receive audio. L=left, R=right, M=mono left+right, S=stereo.
monipan [<monitor1/2> <snd|rcv> <-10...10>]
   Select L/R balance for either send or receive audio.
monoin <+|->
   Switch audio going to the encoder to mono or stereo.
mpvol <0..3> <0..$3f>
   Set input <0..3> volume knob to <0..$3f>
mr 1: <addr> [nbytes] 2: <none>
   Dump CPU memory from given address (1) or continue from previous address (2)
mw <addr> <byte1> [<byte2>]...
   Write one or more bytes to CPU memory
network <isdn|isdnmodem|v35|v35hi|etherrtp|ethersip>
   Select the network type for bitstream I/O.
numbase <bin|dec|hex|<2...16>> [def]
   Set default number base for number input. This affects only the current session. If 'def' is specified then this will be the default number base for all future sessions.
nvf <file number>
   Dump the specified NVRAM file.
nvi 
   Print information on NVRAM status.
nvr [<addr0..7FF>]
   Dump serial EEPROM contents starting with given address or continue dump from last address.
nvwrite <on|off>
   Enable/disable writing of system variables to NVRAM.
pmdump [clear]
   See the status of the last boot
pp ['in' [val]|'out' [val]]
   Override incoming or outgoing parallel port values. Return to normal operation of 'val' is not specified. Read current input & output value if no parameter is given.
ppin [<bit1..8> <endend|auto0|auto1|auto2|auto3|auto4|auto5|auto6|auto7>] or [<endend>|<local>|<lw>]
   Select operation mode for selected parallel port input bit or switch all bits to 'end-to-end' mode or take input bits from local parallel port or take input bits from LiveWire GPIO messages.
ppinv [+|-]
   Switch transparent parallel contact closures inputs to normal/inverted mode.
ppout [<bit1..8> <off|on|endend|lock1|lock2|lock1o2|lock1&2|conn1|conn2|conn1o2|conn1&2>] or [<off|on|endend>]
   Select operation mode for selected parallel port output bits or switch all outputs to 'off' or 'on' or transparent ('endend') mode.
pptest 
   Test the parallel port contact closures. A 1:1 loopback plug must be connected to the parallel port which loops back outputs to inputs in order for this test to work.
quit 
   Log off from the command interpreter.
rcvout [+|-]
   Force Monitor 2 out to receive out and disable frontpanel selector button and Monitor 2 mix selection menus.
reboot ['cold']
   Reboot the unit. Optionally perform a cold boot which resets all settings to their defaults.
remote <command string>
   Send a command to the remote side of an audio connection. When sending a series of commands separate them with a single colon (:).
reset ['cold']
   Reboot the unit. Optionally perform a cold boot which resets all settings to their defaults.
routi 
   Display encoded data routing information.
scnt 
   Return the sample count and sample frequency from the FPGA.
setuptest [count]
   Spawn a thread which tests the flash file system used for SETUPs and AUTODIALs. It will write 'count' (def=1) random AUTODIALs.
sfq <48|44|32>
   Choose system sampling frequency.
sound <<sound#>|<sound file>> [l|d]
   Play one of the available sounds.
soundvol [volume 0..127]
   Set local speaker volume.
split [w <reg> <val>|<tx1ts> <tx2ts> <rx1ts> <rx2ts>]
   Display splitter information.
streamdial <IP address>
   Attempt to establish an ethernet connection to <IP address>
streamdisc [IP address]
   Disconnect an ethernet stream. In RTP mode, IP address is required
streamrcvstats <reset>
   Display stats about received stream, optionally reset
streamsanity 
   report stats on streaming buffer memory usage
streamsndstats 
   Display stats about streams being sent out.
test 
   Test.
ti 
   SOTprint information about specific or all exisiting tasks.
time [current time]
   Display current system time and time difference to previous time command. If 'current time' is specified then it will be used to print out absolute time values in the ISDN log and in various other places.
timezone [<timezone (+-hours)> [DST] [NTP server name or IP]]
   Set the timezone in hours, the NTP server address or host name and optionally enable daylight savings time. This will automatically update the system time!
v35deco [l2|l3|aac|aacld]
   Enter or display the V.35 highspeed decoder algorithm.
v35enco [l2mono|l2stereo|l2joint|l3mono|l3stereo|l3joint|aacmono|aacstereo|aacjoint|aacldmono|aacldstereo|aacldjoint]
   Enter or display the V.35 highspeed encoder algorithm.
v35rate [96|112|128|256|384]
   Enter or display the V.35 highspeed encoder bitrate.
v35test 
   
version 
   Display various version information.
xmtcfg [<buffer-size> <+|-> <bandwidth>]
   Choose modem xmt buffer size (def=10), downsampling (2x/1x) and audio bandwidth for AAC-LD encoder. Display settings when no parameter is specified.
zaesin <analog | conv | sync >
   Select AES/EBU input mode
zaesout [<normal|32|44|48|ext|aesin>]
   Select AES/EBU ouput mode.
zanswer <A+|A->
   Switch ISDN and phone auto-answer on/off
zbaud [<300|600|1200|2400|4800|9600|19200> [1|2]]
   Set RS232 baudrate. The optional additional number of stopbits is ignored.
zbitrate <56/32|64/32|56/48|64/48>
   Select line Bitrate/Sample rate in kbps/kHz, default: 56kbps/32kHz
zconn <1|2> <number> or <1..50>
   Establish Zephyr-type ISDN connection on line 1 or 2 or activate a setup.
zdirec <line0..7> <number|->
   Set or delete MSN resp. DN number.
zdisc <1|2|B>
   Disconnect ISDN on line 1 or 2, or both
zephcmds 
   Obsolete - provided for compatibility.
zlevel <-15 .. +4>
   Select analog/AESEBU input level in dB.
zlog [SYS|ISDN|IMON|SEXT|TIME|ITIM]
   Switch on a combination of logging channels. No parameter will switch off logging.
zloop <off|far|near>
   Loop mode far, near or off, Default off
znetwork <ISDN|V35|Ethernet>
   Select network: isdn, v35, v35hs, etherrtp,ethersip,isdnmodem,potsmodem
zreset 
   Reset Zephyr (warm boot).
zrxmode <L3MO|L3ST|G722|L2|L2HALF|L2MO>
   Select receive mode L3-mono, L3-stereo, G.722, Layer2 stereo, Layer2 24kHz, Layer2 mono, default: L3ST)
zsetup [<1..50>[<-|name <num1|-><num2|-><XmtMode><RcvMode><Rate>[<Compat>]]]
   Display or define setup.
zspids <line0..7> <number|->
   Set or delete SPID number.
zstat 
   Zephyr Remote Stat information ...
ztelco <NI1|PTP|ETS300>
   Select ISDN switch type.
ztxmode <L3DU|L3ST|L3JO|G722|L2MO|L2M128|L2DU|L2JO|L2HALF>
   Select transmit mode. Layer3: dual mono, stereo, joint stereo, G.722, Layer2: mono, mono 128/112kbps, dual stereo, joint stereo, mono 24kHz. Default: L3DU)
zver 
   Display version information.
>>version
Xstream application: 4.0.0r, 2014-11-03 13:16
uClinux kernel     : 2.0.39.uc2
Main FPGA          : 0x18
Audio board FPGA   : 0x08
Audio board CPLD   : 0x02
>>dec
Algo BitR SRint SRext DnSmp ChanMd Stereo Bandw CRC ErrCnt FrmCnt ErrVal  OM
4       0 32000 44100     1 stereo     -1    -1  no     -1      0 FFFFFF   0
Meter: -1 -1  IOspeed=2
 ErrLogCnt SynErrCnt    ErrPtr CfgMemSpc   CfgAddr
    000AB0    000AB0    001020    000001    002A21
P:001010: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001018: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001020: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001028: 010501  010501  010501  010501  010501  010501  010501  010501  
AncMode=-1 AncRate=0 AncBuf=X:$000E00 AncBufLen=256
AncRd=000E00 AncWr=000E00
Lost LOCKS: 0
Unlocked
>>sfq
Encoder mode: L3 Stereo
Decoder mode: Auto (G.722, unlocked)
Sample rate: 48000 Hz
Bitrate    : 64 kbps per channel
Network    : V.35 highspeed
>>endomode
ERROR: Unknown command: endomode
>>encomode
Encoder mode: L3 Stereo
Decoder mode: Auto (G.722, unlocked)
Sample rate: 48000 Hz
Bitrate    : 64 kbps per channel
Network    : V.35 highspeed
>>encomode ?
Command....: encomode <L3dual|L3mono128|L3joint|L3stereo|L2half64|L2mono64|L2mono128|L2joint|L2stereo|G722|AACmono64|AACmono128|AACjoint|AACstereo|AACjoint64|AACLDmono64|AACLDmono128|AACLDjoint|AACLDstereo>
Description: Choose encoding algorithm.
>>encomode aacstereo
OK
>>decomode ?
Command....: decomode <Auto|G722|L2M64|L2|L3D/M|L3|AAC64|AAC|AACLDM64|AACLD>
Description: Choose decoding algorithm.
>>decomode aac
OK
>>dec
Algo BitR SRint SRext DnSmp ChanMd Stereo Bandw CRC ErrCnt FrmCnt ErrVal  OM
4       0 32000 44100     1 stereo     -1    -1  no     -1      0 FFFFFF   0
Meter: -1 -1  IOspeed=2
 ErrLogCnt SynErrCnt    ErrPtr CfgMemSpc   CfgAddr
    000BF5    000BF5    001025    000001    002A21
P:001010: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001018: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001020: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001028: 010501  010501  010501  010501  010501  010501  010501  010501  
AncMode=-1 AncRate=0 AncBuf=X:$000E00 AncBufLen=256
AncRd=000E00 AncWr=000E00
Lost LOCKS: 0
Unlocked
>>v35deco ?
Command....: v35deco [l2|l3|aac|aacld]
Description: Enter or display the V.35 highspeed decoder algorithm.
>>v35deco aac
OK
>>v354deci o
ERROR: Unknown command: v354deco
>>v35deco
V.35 highspeed settings:
Encoder: aacstereo
Decoder: aac
Sample rate: 48000 Hz
Bitrate: 128
Network    : V.35 highspeed
>>dec
Algo BitR SRint SRext DnSmp ChanMd Stereo Bandw CRC ErrCnt FrmCnt ErrVal  OM
4       0 32000 44100     1 stereo     -1    -1  no     -1      0 FFFFFF   0
Meter: -1 -1  IOspeed=2
 ErrLogCnt SynErrCnt    ErrPtr CfgMemSpc   CfgAddr
    000059    000059    001029    000001    002A21
P:001010: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001018: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001020: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001028: 010501  010501  010501  010501  010501  010501  010501  010501  
AncMode=-1 AncRate=0 AncBuf=X:$000E00 AncBufLen=256
AncRd=000E00 AncWr=000E00
Lost LOCKS: 0
Unlocked
>>sfq
Encoder mode: AAC Stereo
Decoder mode: AAC
Sample rate: 48000 Hz
Bitrate    : 64 kbps per channel
Network    : V.35 highspeed
>>v35endo ?
ERROR: Unknown command: v35endo
>>v35enco ?
Command....: v35enco [l2mono|l2stereo|l2joint|l3mono|l3stereo|l3joint|aacmono|aacstereo|aacjoint|aacldmono|aacldstereo|aacldjoint]
Description: Enter or display the V.35 highspeed encoder algorithm.
>>v35enco aac
Bad parameter
>>v35enco aacstereo
OK
>>
>>dec
Algo BitR SRint SRext DnSmp ChanMd Stereo Bandw CRC ErrCnt FrmCnt ErrVal  OM
4       0 32000 44100     1 stereo     -1    -1  no     -1      0 FFFFFF   0
Meter: -1 -1  IOspeed=2
 ErrLogCnt SynErrCnt    ErrPtr CfgMemSpc   CfgAddr
    0001B9    0001B9    001029    000001    002A21
P:001010: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001018: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001020: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001028: 010501  010501  010501  010501  010501  010501  010501  010501  
AncMode=-1 AncRate=0 AncBuf=X:$000E00 AncBufLen=256
AncRd=000E00 AncWr=000E00
Lost LOCKS: 0
Unlocked
>>dec
Algo BitR SRint SRext DnSmp ChanMd Stereo Bandw CRC ErrCnt FrmCnt ErrVal  OM
4       0 32000 44100     1 stereo     -1    -1  no     -1      0 FFFFFF   0
Meter: -1 -1  IOspeed=2
 ErrLogCnt SynErrCnt    ErrPtr CfgMemSpc   CfgAddr
    0002F3    0002F3    001023    000001    002A21
P:001010: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001018: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001020: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001028: 010501  010501  010501  010501  010501  010501  010501  010501  
AncMode=-1 AncRate=0 AncBuf=X:$000E00 AncBufLen=256
AncRd=000E00 AncWr=000E00
Lost LOCKS: 0
Unlocked
>>sfq 48
OK
>>dec
Algo BitR SRint SRext DnSmp ChanMd Stereo Bandw CRC ErrCnt FrmCnt ErrVal  OM
4       0 32000 44100     1 stereo     -1    -1  no     -1      0 FFFFFF   0
Meter: -1 -1  IOspeed=2
 ErrLogCnt SynErrCnt    ErrPtr CfgMemSpc   CfgAddr
    000330    000330    001020    000001    002A21
P:001010: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001018: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001020: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001028: 010501  010501  010501  010501  010501  010501  010501  010501  
AncMode=-1 AncRate=0 AncBuf=X:$000E00 AncBufLen=256
AncRd=000E00 AncWr=000E00
Lost LOCKS: 0
Unlocked
>>v35enco
V.35 highspeed settings:
Encoder: aacstereo
Decoder: aac
Sample rate: 48000 Hz
Bitrate: 128
Network    : V.35 highspeed
>>v35deco
V.35 highspeed settings:
Encoder: aacstereo
Decoder: aac
Sample rate: 48000 Hz
Bitrate: 128
Network    : V.35 highspeed
>>ZXS2 V4.0.0r, 2014-11-03 13:16
Enter '?' for help.
>>ogin Telos
ERROR: Unknown command: ogin
>>login Telos
Logged in with user rights.
>>login lola
Logged in with supervisor rights.
>>sfq
Encoder mode: AAC Stereo
Decoder mode: AAC
Sample rate: 32000 Hz
Bitrate    : 64 kbps per channel
Network    : V.35 highspeed
>>network ?
Command....: network <isdn|isdnmodem|v35|v35hi|etherrtp|ethersip>
Description: Select the network type for bitstream I/O.
>>network v35
Network type: V.35
>>
>>network
Network type: V.35
>>dec
Algo BitR SRint SRext DnSmp ChanMd Stereo Bandw CRC ErrCnt FrmCnt ErrVal  OM
4       0 32000 44100     1 stereo     -1    -1  no     -1      0 FFFFFF   0
Meter: -1 -1  IOspeed=2
 ErrLogCnt SynErrCnt    ErrPtr CfgMemSpc   CfgAddr
    00002A    00002A    00101A    000001    002A21
P:001010: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001018: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001020: 010501  010501  010501  010501  010501  010501  010501  010501  
P:001028: 010501  010501  010501  010501  010501  010501  010501  010501  
AncMode=-1 AncRate=0 AncBuf=X:$000E00 AncBufLen=256
AncRd=000E00 AncWr=000E00
Lost LOCKS: 0
Unlocked
>>