AT$ OK  omni.net plus User's Manual Quick Reference Guide For Firmware Version 4.20 and higher BASIC 'AT' COMMANDSET Command Function & Description Ref. A/ Re-execute the last command once. A> Re-execute the last command once or repeat the last call up to 9 times. (See also S8) Terminate current connection attempt when enter in handshaking state. +++ Escape sequence code, entered in data state, wait for omni.net+ to return to command state. ATA Go on-line in answer mode. (See also S39b2) ATBnn Select ISDN Teleservice S102 'B' must be followed by two digits. ------------------------------------------------------------------------------- HELP show function of keypad keys Q quit current buffer #keypad : (Num Lock) Up one line in buffer Top of Ŀ buffer --> 7 8 9 <-- Page up ͵ ͵ 2 3 <-- Page down Down one line in buffer (you can use these keys to continue) ------------------------------------------------------------------------------- B0n X.75 : B00 X.75 Transparent B01 X.75 T.70 B04 BTX (Datex-J) B10 V.110 User rate follows DTE speed B13 V.110 user rate = 2400 bps B14 V.110 user rate = 4800 bps B15 V.110 user rate = 9600 bps B16 V.110 user rate = 14400 bps B17 V.110 user rate = 19200 bps B18 V.110 user rate = 38400 bps (async only) B19 V.110 user rate = 57600 bps (async only) B20 V.120 B40 PPP async to sync conversion B41 SLIP to sync HDLC conversion B42 EuroFile Transfer Multi Auto Dial Out (valid only if s80.6=1) B90 PPP+X.75 S122 B91 PPP+X.75+T.70+ISO_8208+T.90+BTX B92 X.75+T.70+ISO_8208+T.90+BTX+PPP B93 PPP+V.120 B94 V.120+PPP B95 PPP+X.75+V.120 B96 PPP+V.120+X.75 B97 X.75+V.120+PPP ATBPn n=0-1 Configuration PPP BACP/BAP negotiation BP0 Disable PPP BACP/BAP BP1 * Enable PPP BACP/BAP ATCBn n=0-1 Configuration of embedded protocol analyzer S84b1 CB0 Disable the capture of B channel protocols CB1 Enable the capture of B channel protocols ATCCn n=0-1 Configuration of embedded protocol analyzer S84b0 CC0 Disable the capture of DTE-DCE interface protocols CC1 Enable the capture of DTE-DCE interface protocols ATCDn n=0-1 Configuration of embedded protocol analyzer S84b2 CD0 Disable the capture of D channel protocols CD1 Enable the capture of D channel protocols ATCEn n=0-1 Call bumping control for PPP/MP S85b0 CE0 Disable the call bumping function CE1 * Enable the call bumping function ATCF(transfer_no.) For USA NI-1 & DMS-100 switch, activate the call forwarding variable function from the swtich. (Note!You should issue AT&ZF4=n first,n=IOC of CFV) ATCF For USA NI-I & DMS-100 switch, deactivate the call forwarding variable. ATCFxy(tranfer_no.) For DSS1,active the call forwarding service ATCFxy Deactivate the call forwarding service x=B Call forwarding busy(CFB) U Call forwarding unconditional(CFU) NR Call forwarding no-reply(or no-response,CFNR) y=S All services I ISDN data(unrestricted digital) A POTS 1, phone1 B POTS 2, phone2 ATCF? Query the status of call forwarding(DSS1 only) ATCG Diagnostics ATCH? Display the accumulated charging unit of the last call. ATCI Prefix number string to be added to the Calling-party-number before indicating to the DTE when the type of number denotes international. ATCLn n=0-2048 Maximum size of user data in a packet (number of bytes) ATCL? Enquire current setting of ATCLn ATCN Prefix number string to be added to the Calling-party-number before indicating to the DTE when the type of number denotes national. ATCPn n=0-1 Loopback 4 control S83b0 CP0 Disable Loopback 4 CP1 Enable Loopback 4 ATCRn n=0-3 *0 Resumes a previously suspended call, n is the call identifier(DSS1) ATCSn n=0-3 *0 Suspend a call, n is the call identifier(DSS1) ATCT Clear buffer and start the embedded protocol analyzer. Capture data immediately and start timer. ATC$ Invoke the interpretation function of the embedded protocol analyzer and display the results on DTE ATDs Dial s (number and options) that follows (see also S38b0, S35b4). The options of s are listed as follows : , Pause for a time specified in S8. Remaining digits will be dialed as in-band DTMF. Y0 * Unknown type of number Y1 International number Y2 National number Y3 Network specific number Y4 Subscriber number Y6 Abbreviated number Z0 * Type of subaddress - NSAP with AFI=$50, IA5 characters Z2 Type of subaddress - user specified, IA5 characters N0 * Unknown numbering plan N1 ISDN/Telephony numbering plan (CCITT E.164/ E.163) N3 Data numbering plan (CCITT X.121) N8 National standard numbering plan N9 Private numbering plan / Called party subaddress delimiters The format of s will be : [[Yn][Nn]called_party_Number][[W][,]]inband_dtmf_number or [[Yn][Nn]called_party_Number][/[Zn]called_party_subaddress/] ATDAs Dial s (number and options) that follows for the POTS port, Phone 1 ATDBs Dial s (number and options) that follows for the POTS port, Phone 2 ATDIs Dial s (number and options) that follows for ISDN data call ATDL Repeat last ATD command ATDNn n=0,1 Set the Directory Numbers (USA) ATDN0=xxxxxx set the DN0 value ATDN0= clear the DN0 ATDN? query present DNs ATDSn n=0-39 Dial number stored in NVRAM at location 'n', S44b3 use '+' to dial two consecutive numbers for bundling or PPP/MP calls ATEn Command mode local echo of keyboard commands. S23b0 E0 Echo off E1 * Echo on ATHn On/off hook control H0 * Hang up (on-hook) ISDN Data Call, same as 'ATH' H1 Go off-hook H3 Hang up the POTS port, Phone 1 H4 Hang up the POTS port, Phone 2 ATHWR Hardware reset S38b2 ATIn Display inquired information I0 Display product code, same as 'ATI'. Results: 1291 (USA) 1292 (DSS1) 1293 (1TR6) I1 Display product information and ROM checksum Results: omni.net : V x.xx where = USA, DSS1, or 1TR6 I3 Display link status report of ISDN call I9 Display Microsoft PnP code I11 Display PPP status. ATJAn n=0-255 *48 Add-threshold for PPP/MP Bandwidth-On-Demand S126 in Kbps unit, ATJSn n=0-255 *32 Sub-threshold for PPP/MP Bandwidth-On-Demand S127 in Kbps unit ATJHn PPP/MP DTE compression option switch n=0 Disable DTE compression, compression done by TA n=1* Enable DTE compression if available ATKAxn n=0-63 *0 Add-persist time interval for BOD, S85b1-7 BOD disabled if n=0 x= M(in Minute unit) or S(in Second unit) ATKSxn n=0-63 *0 Sub-persist time interval for BOD, S125b1-7 x= M(in Minute unit) or S(in Second unit) ATLn n=0-3 *2 Speaker volume control. The higher the value S24b4-5 ,the higher the volume. ATMn Speaker control. S21b1-2 M0 Speaker always OFF. M1 * Speaker ON until call is answered. M2 Speaker always ON. ATMW For USA NI-1 message waiting service, disable the audible & feature message waiting. ATNn n=0-3 *2 Ring volume control.'N0' will disable S24b0-1 the ring function. ATO Return to on-line state ATPn n=0-6 D-channel protocol selection(USA) for American Version P0 * Northern Telecom proprietary ISDN P1 National ISDN 1(1 SPID) P2 National ISDN 1(2 SPID) P3 reserved P4 AT&T proprietary point-to-point P5 AT&T proprietary point-to-multipoint(1 SPID) P6 AT&T proprietary point-to-multipoint(2 SPID) ATQn Result code displayed S23b7 Q0 * omni.net+ returns result code. Q1 omni.net+ does not return result code. Q2 omni.net+ returns result code but quiet after S40b1 answering on a RING. (will not show in AT&Vn) ATQPn QP1 Display the setting of quick dial (speed dial) numbers QP2 Display the call-out history QP3 Display the call-in history ATSr.b=n Set bit 'b' of S-register 'r' to value 'n'. 'n' is a binary digit '0' or '1'. ATSr.b? Display value of bit 'b' of S-register 'r'. ATSr=n Set S-register 'r' to value 'n'. 'n' must be a decimal number between 0 and 255. ATSr? Display value stored in S-register 'r'. ATSD? Display current Date of omni.net LCD. ATSD=yyyy/mm/dd Set Date of omni.net LCD.(Note! yyyy:year, mm:month , dd:day) ATST? Display current Time of omni.net LCD. ATST=hh:mm:ss Set Time of omni.net LCD (Note! hh:hour, mm:munite, ss: second) ATSPIDr=nnn... User enters Service Profile ID nnnn...(USA only) SPID0 First SPID number SPID1 Second SPID Number, if any ATSPID? Display the SPID setting(s) (USA only) ATSWR Software reset S38b2 ATUNIT=xxxx (0.001 ->65) save the charging fee per unit to NVRAM. ATUNIT? view the value of charging fee per unit. ATUPX Upload firmware to the Flash EPROM ATVn Verbal/Numeric result codes. S23b6 V0 Display result code in numeric form. (See also S35b7 and the result code table of 'ATXn') V1 * Display result code in verbose form. ATXn n=0-8 *5 Result code options, see the Options Table S23b3-5 ATYn n=0-6 *0 Caller ID signaling option ( for CLID hardhware) Y0 by country default Y1 DTMF, prior to ring Y2 ETSI FSK, during ring Y3 ETSI FSK, prior to ring. Y4 Bellcore FSK, during ring Y5 Bellcore FSK, prior to ring Y6 DTMF, during ring ATZn n=0-4 Reset omni.net+ and set power-on profile. S15b5-7 Zn Reset omni.net+ and load user profile n (0-3). Z4 Reset omni.net+ and load factory settings. AT$ Basic command summary help EXTENDED 'AT&' COMMAND SET Command Function & Description Ref. &Cn Carrier Detect (CD) options S21b4 &C0 CD always ON (See also S42b7) &C1 * CD tracks presence of carrier. (See also S38b3) &Dn Data Terminal Ready (DTR) options. S21b6-7 (See also S25) &D0 Ignore DTR signal, assume DTR is always ON. &D1 108.1, DTR OFF-ON transition causes dial of the default number. (See also 'AT*Dn' and S48b4) Note: This function is ignored when power on. &D2 * 108.2, Data Terminal Ready, DTR OFF causes the omni.net+ to hang up. &D3 Same as &D2 but DTR OFF causes the omni.net+ to hang up and reset from profile 0. &En B channel line speed for ISDN data call S118b2 &E0 * 64Kbps &E1 56Kbps (Default for American ISDN) &F Load factory settings to RAM as active configuration. &Hn DTE port 1 Data flow control, DTE/DCE. S27b3-5 &H0 Flow control disabled. &H3 * Hardware (CTS/RTS) flow control. &H4 Software (XON/XOFF) flow control. &Jn Bundle selection (See also S100) S87b5-6 &J0 * Bundle connection is disabled &J1 Bundle connection is enabled in answer mode only &J2 Bundle connection is enabled in call mode only &J3 Bundle connection is enabled in both directions &Knn PPP/V.120/X.75 data compression control &K must be followed by two digits S83b2 &K00 Disable compression &K44 Enable V.42bis (PPP/V.120/X.75), STAC (PPP) &Ln POTS port selection during call answering S84b5 &L0 Set priority to POTS port, Phone 1 &L1 Set priority to POTS port, Phone 2 &On Set default call type for conventional dialing S83b4-5 commands &O0 ATDs, ATDPs, and ATDTs default to make calls for the POTS port, Phone 2 &O2 ATDs, ATDPs, and ATDTs default to make ISDN data calls &O3 ATDs, ATDPs, and ATDTs default to make calls for the POTS port, Phone 1 &Sn Data Set Ready (DSR) function selection. S21b3 &S0 * DSR overridden, DSR always ON. &S1 DSR according to CCITT (ITU-TSS). (See also S41b5, S44b4) &Tn omni.net+ testing. &T9 Initiate ISDN loopback test &T10 Initiate ISDN loopback with self test &T11 Initiate ISDN loopback from B1 through switch to B2. &Vn View profile settings. &V0 View current active settings. &Vn View the (n-1)th user profile settings (n=1-4) &V5 View factory default settings. &V6 View POTS port, Phone 1 setting &V7 View POTS port, Phone 2 setting &V8 System Resources Status &Wn n=0-3 Write current settings to user profile n in NVRAM. (See also S35b6) &Z? Display all the phone numbers stored in NVRAM. &Zn=s n=0-39 Write phone number s to NVRAM at location n (n=0-39) use AT*Dn or ATS29=n to set the default dial pointer. &ZIn=s n=0-7 Assign the phone number (including subaddress, if any) for various B-channel protocols. In answer mode, these numbers will be compared with the received called party number or called party subaddress information. The call will be accepted using the specific protocol if the assigned number of this protocol matches with the called party number. &ZI0=s Assign the phone number for X.75 &ZI1=s Assign the phone number for V.110 &ZI2=s Assign the phone number for V.120 &ZI3=s Assign the phone number for PPP, PPP/MP &ZI4=s Assign the phone number for ISDN data (Multi-Auto answering, auto detect the protocols) &ZI6=s Assign the phone number for POTS port, Phone 2 &ZI7=s Assign the phone number for POTS port, Phone 1 &ZI? Display the phone number (including subaddress , if any) for various B-channel protocols &ZFn=s n=0-4 For USA NI-1 switch only, assign the relative ISDN s=0-63 Ordering Code, IOC(or dial access code) for each supplementary service &ZF0=s Assign the IOC for Conference &ZF1=s Assign the IOC for Drop &ZF2=s Assign the IOC for Transfer &ZF3=s Assign the IOC for Message Waiting &ZF4=s Assign the IOC for Call Forwarding &ZF? Show the setting of AT&ZFn=s &ZPx=s Write service provider preselect number The number secified by &ZPx will be inserted in the front of the called party number while dialing x=I(ISDN), A(POTS port, phone1) or B(POTS port, phone2) (DSS1 only) &ZP? Display the service provider preselect numbers assigned via the AT&ZPx=s command (DSS1 only) &ZOx=s Write own phone number (including subaddress, if any). The number secified by &ZOx will be used as the calling party number while dialing x = I(ISDN), A(POTS port, Phone 1) or B(POTS port, Phone 2) (DSS1 only) &ZO? Display the own phone numbers assigned via the AT&ZOx=s command (DSS1 only) EXTENDED 'AT*' COMMAND SET Command Function & Description Ref. *Cn Character length, including start, stop S15b3-4 and parity bit. *C0 * DTE port 10-bit character length. *Dn n=0-39 Set default dial pointer at telephone S29 directory location n. *D0 * (See also S35b4 and S38b0) *Gn Security function selection. S36b5-7 *G0 * Disable security function. *G1 Enable type 1 security, with password check (Proprietary). *G2 Enable type 1 security, with password check and call back (Proprietary). *G3 Enable type 2 security, with password check. *G4 Enable type 2 security, with password check and call back. *G5 Enable type 2 security, with password check and call back, remote site enters the call back number. *GCn Call-back function selection. S119b0 *GC0 * Disable call-back function. *GC1 Enable call-back function *HCn n=0-4 Assign call back phone number. *Hn n=0-39 Modify user password table at location n. *HS Modify supervisory password (Default: see user's manual). *T Recall the last CND (Caller ID) information. *V View password table *VC View call-back number table BASIC S-REGISTER, 'ATSn=x' Command Function & Description S0= Set the number of rings on which the omni.net+ will answer. 0 value disable auto-answer +000 S1= Counts and stores number of rings from an incoming ca11 +000 S2= Define escape codecharacter, default <+> (43 dec.) +043 S3= Define ASCII Carriage Return +013 S4= Define ASCII Line Feed +010 S5= Define ASCII Backspace +008 S7= Set duration, in number of seconds, omni.net+ waits for a connect +060 S8= Set duration, in seconds, for pause (,) option in Dial command and pause between command re-executions for Repeat (>)command +002 EXTENDED S-REGISTERS, 'ATSn=x' Command Function and description +Def./Ref. S14= bit dec hex Bit-mapped register: +002 0 0 0 TA auto-handshake mode on originate mode. 1 1 TA auto-handshake mode on answer mode S15= bit dec hex Bit-mapped register +130 0,1 0 0 Even parity 2 2 * No parity 2 0 0 * 1 stop bit 4,3 0 0 * 10 bit character length *C0 7-5 0 0 Profile 0 as active settings after power on Z0 32 20 Profile 1 as active settings after power on Z1 64 40 Profile 2 as active settings after power on Z2 96 60 Profile 3 as active settings after power on Z3 128 80 * Factory default as active settings after power on Z4 S16= bit dec hex Test status register +000 0 0 No test in progress 9 9 Loopback test in progress &T9 10 A Loopback with self test in progress &T10 11 B loopback from B1 through switch to B2 &T11 S18= dec Force omni.net+ to fix DTE port baud +000 rate when idle 0 * Disable fixed baud function 1-14,32 1-E,20 Enable baud rate to be fixed when answering baud rate value setting same as S20 except S18=32 for 230400 bps. S20= dec hex DTE port speed (bps). Auto detected from AT command +003 0 0 230400 1 1 115200 3 3 57600 4 4 38400 5 5 19200 9 9 9600 11 B 4800 12 C 2400 13 D 1200 14 E 460800 15 F 921600 S21= bit dec hex Bit mapped register +178 1-2 0 0 Speaker always Off M0 2 2 Speaker ON until call is answered. M1 4 4 Speaker always On M2 3 0 0 DSR always On &S0 8 8 According to CCITT (see also S44b4, &S1 S41b5) 4 0 0 CD always On &C0 16 10 CD tracks presence of data connection &C1 (see also S38b3) 5 0 0 CTS follows RTS, in synchronous mode &R0 32 20 Ignore RTS (CTS always On), in &R1 synchronous mode 6-7 0 0 Assume DTR always On &D0 64 40 108.1, DTR Off-On transition causes &D1 dial of the default number 128 80 108.2 Data Terminal Ready, DTR Off &D2 causes the omni.net+ to hang up and return to command state 192 C0 108.2, DTR off causes the omni.net+ &D3 to hang up and reset the omni.net+ to profile #0 after DTR dropped S23= bit dec hex Bit mapped register +105 0 0 0 Command echo disabled E0 1 1 Command echo enabled E1 2 0 0 Insertion is not allowed during a phone call 4 4 Insertion is allowed during a phone call 3-5 0 0 ATX0 (See result code table) 8 8 ATX1 dec hex AT 16 10 ATX2 40 28 X5 24 18 ATX3 48 30 X6 32 20 ATX4 56 38 X7 6 0 0 Display result code in numeric format V0 (see S35b7) 64 40 Display result code in verbose format V1 7 0 0 TA returns result code Q0 128 80 TA does not return result code (see Q1 (see also S40b1) S24= bit dec hex Bit mapped register +34 0-1 0-3 0-3 Ring volume control, increments of 1 N0-3 in decimal 2 0 0 The setting of s21(b1-2) ignored when phone 1 key pad dial 1 1 The setting of s21(b1-2) will be affected to phone 1 key pad dial 3 0 0 The setting of s21(b1-2) ignored when phone 2 key pad dial 1 1 The setting of s21(b1-2) will be affected to phone 2 key pad dial 4-5 16-48 0x10- 0x30 Speaker volume control, L0-3 increments of 16 in decimal value 6 0 0 POTS port tone Volume low 1 1 POTS port tone Volume Hi S27= bit dec hex Bit mapped register +156 3-5 0 0 DTE port Flow control disabled &H0 24 18 DTE port Hardware (RTS/CTS) flow control &H3 40 28 Reserved &H5 S29= 0-39 0-39 Set default dial phone number pointer, +000 use AT&Zn=s to store phone numbers *D S31= 0-255 0-FF Holds the ASCII decimal value of the +017 XON S32= 0-255 0-FF Holds the ASCII decimal value of the +019 XOFF S35= bit dec hex Bit mapped register +000 4 16 10 When Button switch is pushed, *DnS29 omni.net+ will dial the default number 6 64 30 Enable password protection to profile &Wn saving, when is issued, and the n profile in the memory has this bit on, supervisory password will be requested 7 128 60 Enable extended numerical result codes V0 from 50-71 when an error correction S23b6 connection is made, use with ATV0, see result code table S36= bit dec hex Bit mapped register +000 5-7 Security function control register *0 0 Disable security function *G0 32 20 Enable type 1 security, with password *G1 check (Proprietary) 64 40 Enable type 1 security, with password *G2 check and call-back (Proprietary) 96 60 Enable type 2 security, with password *G3 check 128 80 Enable type 2 security, with password *G4 check and call-back 160 A0 Enable type 2 security, with password *G5 check and call-back, remote site enter the call-back number S38= bit dec hex Bit mapped register +000 0 1 1 Repeatedly dialing default number *DnS29 1-2 Reserved 2 4 4 Key for ATSWR ,ATHWR 3 8 8 DCD on/off sequence follows UNIX &C1,S21b4 standard, DCD high before connect message is sent, DCD off after last DCE response is sent S40= bit dec hex Bit mapped register +000 1 2 2 No result code displayed in answer Q2 mode S41= bit dec hex Bit mapped register +000 3 8 8 Enable CCITT signals 140 and 141 on EIA-232D interface 5 32 20 DSR follows DCD and pulses (see also &Sn S44b4) 6 64 40 Force S0>=2 S0 S42= bit dec hex Bit mapped register +000 3 8 8 Disable escape sequence code in answer mode 5 32 20 Disable Data/Voice button 6 64 40 Disable result code Xn 7 128 80 DCD forced on but pulse off for 0.5 &C0 seconds at carrier loss S44= bit dec hex Bit mapped register +000 3 8 8 ATDSn initiates auto-dial of the &Zn stored numbers consecutively until a S38b0 connection is made 4 16 10 DSR follows DTR (see also S41b5) &Sn S50= 0-255 Inactivity timer for RS 232 port +000 this timer counts when there is no data flow in or out of the RS 232 serial port; TA will hang up , when timed out. units is 10 seconds! 000 disables timer S56= dec hex Hook flash detected time for POTS port +050 0-255 0-FF adapter, in units of 10ms default setting 50 = 0.5 seconds S61 bit dec hex 3 *0 0 MP data sent in rotate mode 1 1 MP data sent in split mode S64 dec hex Security callback timer in unit +005 0-255 0-FF of 1 second S78= bit dec hex Bit-mapped register: 0 *0 0 can get busy tone from phone 1. 1 1 can not get busy tone from phone 1. 1 0 0 can get busy tone from phone 2. 2 2 can not get busy tone from phone 2. 2 *0 0 Disable the 'RING' message to DTE port for analog call 4 4 Enable the 'RING' message to DTE port for analog call S79= bit dec hex Bit-mapped register: +000 0 *0 0 Ignore POTS port 1 global incoming call when port 1 busy 1 1 Discard POTS port 1 global incoming call when port 1 busy (Sending RELEASE COMPLETE) 1 *0 0 Ignore POTS port 2 global incoming call when port 1 busy 2 2 Discard POTS port 2 global incoming call when port 1 busy (Sending RELEASE COMPLETE) 2 0 0 POTS 1 call-waiting/multiple-answer disabled *4 4 POTS 1 call-waiting/multiple-answer enabled 3 0 0 POTS 2 call-waiting/multiple-answer disabled *8 8 POTS 2 call-waiting/multiple-answer enabled 4 *0 0 POTS port 1 is connected to telephone 16 10 POTS port 1 is connected to Fax/Modem 5 *0 0 POTS port 2 is connected to telephone 32 20 POTS port 2 is connected to Fax/Modem 7 *0 0 Sending RELEASE COMPLETE with cause 'call reject' for ATH1 128 80 Sending RELEASE COMPLETE with cause 'user busy' for ATH1 S80= bit dec hex Bit-mapped register: +000 4 *0 0 Not sending Low Layer Compatibility information for POTS port 2 16 10 Sending Low Layer Compatibility for POTS port 2 6 *0 0 Not sending Low Layer Compatibility information for ISDN data call 64 40 Sending Low Layer Compatibility for ISDN data call 7 *0 0 Not sending Low Layer Compatibility information for POTS port 1 128 80 Sending Low Layer Compatibility for POTS port 1 S82= ISDN B channel protocol Bn 60 V.120 64000 61 V.120 56000 62 X.75 64000 Transparent 63 X.75 56000 Transparent 64 X.75 64000 T.70 65 X.75 56000 T.70 70 X.75 64000 BTX 71 X.75 56000 BTX 72 V.110 64000 73 V.110 56000 74 PPP async to sync 64K 75 PPP async to sync 56K 76 SLIP to sync HDLC conversion 64K 77 SLIP to sync HDLC conversion 56K S83= bit dec hex Bit-mapped register: +000 0 0 0 Disable loopback 4 test CP0 1 1 Enable loopback 4 test CP1 2 0 0 ISDN without V.42bis &K00 4 4 ISDN with V.42bis if applicable &K44 4-5 0 0 * ATDs, ATDPs, and ATDTs is mapped &O0 to ATDBs 32 20 ATDs, ATDPs, and ATDTs is mapped &O2 to ATDIs 48 30 ATDs, ATDPs, and ATDTs is mapped &O3 to ATDAs 6 0 0 * DOVBS answer using 56Kbps (for USA only) 64 40 DOVBS answer using 64Kbps 7 0 0 * ISDN data call using normal Bearer Service (for USA only) 128 80 ISDN data call using voice Bearer Service S84= bit dec hex 0-2 Embedded protocol analyzer control CCn 0 1 1 Capture DTE-DCE interface protocol information 1 2 2 Capture the B-channel (X.75 or V.120) frames 2 4 4 Capture the D-channel protocol information 3 0 *0 Display S register value in decimal format 8 8 Display S register value in hex format 4 *0 0 Indicate Caller ID after the 1st RING message 16 10 Disable Caller ID indication 5 0 0 POTS port 1 has higher priority for &L0 answering the analog call. 32 20 POTS port 2 has higher priority for &L1 answering the analog call. S85= bit dec hex 0 0 0 Call Bumping function disabled CE0 1 *1 Call Bumping function enabled CE1 1-6 *0 Add-persist time interval KAxn 7 0 *0 S85b1-6 is in Second unit KASn 128 80 S85b1-6 is in Minute unit KAMn S87= bit dec hex 0 *0 0 Enable POTS port 1 receive global call 1 1 Disable POTS port 1 receive global call 1 *0 0 Enable POTS port 2 receive global call 2 2 Disable POTS port 2 receive global call 2 *0 0 CHAP/PAP for authentication conversion 4 4 PAP only for authentication conversion 4 *0 0 result code 46 for X7 is CONNECT 112K/.. result code 47 for X7 is CONNECT 128K/.. 16 10 result code 46 for X7 is CONNECT 112000/.. result code 47 for X7 is CONNECT 128000/.. 5-6 *0 0 Bundle connection is disabled &Jn 32 20 Bundle connection is enabled in answer mode only 64 40 Bundle connection is enabled in call mode only 96 60 Bundle connection is enabled in both directions S89= bit dec hex Bundle and data encryption control 5 0 0 disable the metering pulse of POTS port 2 32 20 enable the metering pulse of POTS port 2 6 0 0 disable the metering pulse of POTS port 1 64 40 enable the metering pulse of POTS port 1 S90= bit dec hex 0 0 0 reserved 1 *0 0 AT&F set factory default 2 2 treat AT&F as ATZ S91= bit dec hex 0 *0 0 no call restriction on phone A 1 1 cannot make long distance call by phone A 1 *0 0 no call restriction on phone B 2 2 cannot make long distance call by phone B S100= dec hex B channel bundling protocol selection 0 0 * Multiple Link Protocol (MLP) S102= bit dec hex Outgoing ISDN data type Bnn Value has the same definition as S82 S104+n= dec hex Outgoing Service Indicator (for 1TR6 only) n = 0(POTS port, Phone 2), 2(ISDN data), or 3(POTS port, Phone 1) 1 1 Fernsprechen 2 2 a/b - Dienste 7 7 Datenbertragung 64 kbps. The defaults are : * s104=1 - for POTS port 2 * s105= - reserved * s106=7 - for ISDN data * s107=1 - for POTS port 1 S108+n= dec hex Outgoing Service Additional (for 1TR6 only) Information n = 1(POTS port, Phone 2), 2(ISDN data), or 3(POTS port, Phone 1) SI=1 1 1 * ISDN-Fernsprechen 3.1 kHz 2 2 Fernsprechen analog SI=2 2 2 Fax Gruppe 3 3 3 * Daten ber Modem 4 4 Btx ber Modem SI=7 0 0 Datenbertragung 64 kbps (X.75 SLP) 11------ Async V.110 01------ Extensions of async --0----- * Number of data bits : 8 --1----- Number of data bits : 7 ---0---- * Number of stop bits : 1 ---1---- Number of stop bits : 2 ----0--- * No parity ----1--- Even parity 11---000 1200 bps 11---011 2400 bps 11---100 4800 bps 11---101 9600 bps 11---110 14400 bps 11---111 * 19200 bps 01---000 38400 bps 1010---- Sync V.110 10100000 1200 bps 10100011 2400 bps 10100100 4800 bps 10100101 9600 bps 10100110 14400 bps 10100111 19200 bps 10101000 48000 bps 10101001 56000 bps 10101010 56000 bps for 56kbit-network 10101111 In band negotiation S108+n= dec hex High Layer Compatibility (Non-1TR6) n = 1(POTS port, Phone 2), 2(ISDN data), or 3(POTS port, Phone 1) *0 0 No High-Layer-Compatibility information element will be sent 1 1 Telephone 4 4 Facsimile Group 2/3 40 28 Teletex service(Rec.F.220) 49 31 Teletex service(Rec.F.200) 50 32 Information interworking for video services(Rec.F.300 T.110) 53 35 Telex service(Rec.F.60) 56 38 Message Handling Syxtems(MHS) (Rec.X.400 series) 65 41 OSI application(Rec.X.200 series) S114= I-field data length (MSB byte) S115= I-field data length (LSB byte) S117= V.110 user rate B1n S118= bit dec hex 0 *0 0 Enable dial-in call 1 1 Disable dial-in call(dial out only) 2 *0 0 Default B channel line speed is 64Kbps for ISDN data call &E0 4 4 Default B channel line speed is 56Kbps for ISDN data call &E1 3 *0 0 Disable DTE CHAP option for PPP/MLPPP, CHAP done by TA 8 8 Enable DTE CHAP option for PPP/MLPPP 4 *0 0 Use 3.1KHz Bearer service whenever possible for POTS port, Phone 2 16 10 Use Speech Bearer service whenever possible for POTS port, Phone 2 5 *0 0 Use 3.1KHz Bearer service whenever possible for POTS port, Phone 1 32 20 Use Speech Bearer service whenever possible for POTS port, Phone 1 6 *0 0 Enable the a/b adapter to accept globalcalls 64 40 Forbid the POTS port to accept global calls 7 *0 0 Enable analog incoming calls 128 80 Reject analog incoming calls (pure ISDNdata) S119= bit dec hex 0 *0 0 Disable call-back function(see AT*GC) 1 1 Enable call-back function 1 *0 0 D-channel layer-2(LAPD) 'point-to-multipoint' operation mode (dynamic TEI,64 <= n <= 126). 2 2 D-channel layer-2(LAPD) 'point-to-point' operation mode (static TEI=0). 2 *0 0 Disable'overlap receiving'signaling function (for ISDN supplementary service 'MSN'). 4 4 Enable'overlap receiving'signaling (for ISDN supplementary service DDI). 3 *0 0 when no MSN(EAZ) is matched, the inbound call will be ignored NOTE: default = 1 for USA, default = 0 for others 8 8 when no MSN(EAZ) is matched, use default protocol to accept 4 0 0 V.110 user rate = 19200 bps if DTE speed greater 19200 bps *16 10 V.110 user rate = 38400 bps if DTE speed greater 38400 bps 5 *0 0 enable normal MSN function &Zin= 32 20 treat the number assigned by &ZIn=xx.. as subaddress and matches with the called party subaddress for inbound call routing S120= bit dec hex 0 *0 0 Enable POTS port 1 call out 1 1 Disable POTS port 1 call out 1 *0 0 Enable POTS port 2 call out 2 2 Disable POTS port 2 call out 2 *0 0 Enable multi-answering while TA MSN is not assigned ,global call or MSN matched both POTS then both POTS will ring. 4 4 Handle incoming call according to AT&Ln setting. 3 *0 0 While S120.2=1 is set and the POTS port is busy, this call will be routed to another POTS port. 8 8 While S120.2=1 is set and the POTS port is busy ,this call will be rejected. 4 *0 0 Enable omni.net+ to accept global calls for a/b adapter and ISDN data. 16 10 Forbid omni.net+ to accept incoming calls with MSN unmatched for a/b adapter and ISDN data. (including global calls, see AT&ZI=s) 5 *0 0 Reserved 6 *0 0 Disable supplementary service 'CLIR'(Calling Line Identification Restriction). 64 40 Enable supplementary service 'CLIR'(Calling Line Identification Restriction). 7 0 0 Feature (flex)phone functions are enable when press flash key on the phone set. 128 80 Supplementary service functions are enable when press flash key on phone set. (For USA default=1, for DSS1 default=0) S121= bit dec hex Programmable ring frequency, using follow 0-1 0-3 0-3 value to choose ring frequency: *0 0 50Hz 1 1 30Hz 2 2 25Hz 3 3 20Hz 3 *0 0 Display CLID info. With the first RING message 8 8 Display CLID info. With each RING message 4 *0 0 D channel L2 send DISC actively 16 16 D channel L2 doesn't sent DISC 2, 5-7 Reserved S122= bit dec hex 0-1 0-3 0-3 Select a preferred BXchannel for outgoing data call(USA only) *0 0 Any channel 1 1 Reserved 2 2 B1-channel preferred 3 3 B2-channel preferred 2-4 0-28 0-28 Set sequence for multi auto dial out 0 0 PPP+X.75 4 4 PPP+X.75+T.70+ISO_8208+T.90+BTX 8 8 X.75+T.70+ISO_8208+T.90+BTX+PPP 12 C PPP+V.120 16 10 V.120+PPP 20 14 PPP+X.75+V.120 24 18 PPP+V.120+X.75 28 1C X.75+V.120+PPP 5 0 0 Disable multi auto dial out 32 20 Enable multi auto dial out 6 0 0 Choose MDMF format as FSK caller ID output 40 64 Choose SDMF format as FSK caller ID output S123= bit dec hex 0-1 0-3 0-3 Select Caller ID signaling method *0 0 Country default. 1 1 DTMF, prior to ring. 2 2 ETSI FSK, during ring 3 3 ETSI FSK, prior to ring. 2-7 Reserved S124= dec hex Empty IP packet interval for PPP +000 0-255 0-FF in units of 1s S125= bit dec hex 1-6 *0 Sub-persist time interval KSxn 7 0 *0 S125b1-6 is in Second unit KSSn 128 80 S125b1-6 is in Minute unit KSMn S126= dec hex Add-threshold for BOD Jan,+48 0-255 0-FF in Kbps unit S127= dec hex Sub-threshold for BOD JSn,+32 0-255 0-FF in Kbps unit In 'Reference' column, 'AT' is omitted when AT command is referred to. +nnn is manufacturer default when listed in 'Reference' column. bit S-register bit number, 'b', used in 'ATSr.b=n', 'ATSr.b=?' dec Decimal value, 'x', used in 'ATSn=x' hex Hex value, used in LCD model for setting 'STATUS REGISTER' manually from front panel RESULT CODE OPTIONS TABLE ATV0 ATV1 ATX0 X1 X2 X3 X4 X5 X6 X7 X8 0 OK V V V V V V V V V 1 CONNECT V V V V V @ $ # & 2 RING V V V V V V V V V 3 NO CARRIER V V V V V V V V V 4 ERROR V V V V V V V V V 5 CONNECT 1200 % % % % @ $ # & 6 NO DIAL TONE V V V V V V 7 BUSY V V V V V V 8 NO ANSWER V V V V V V 9 RINGING* V V V V V V 10 CONNECT 2400 % % % % @ $ # & 11 CONNECT 4800 % % % % @ $ # & 12 CONNECT 9600 % % % % @ $ # & 14 CONNECT 19200 % % % % @ $ # & 15 CONNECT 7200 % % % % @ $ # & 16 CONNECT 12000 % % % % @ $ # & 17 CONNECT 14400 % % % % @ $ # & 18 CONNECT 16800 % % % % @ $ # & 19 CONNECT 38400 % % % % @ & 20 CONNECT 57600 % % % % @ & 21 CONNECT 76800 % % % % @ & 22 CONNECT 115200 % % % % @ & 23 CONNECT 230400 % % % % @ & 24 CONNECT 460800 % % % % @ & 25 CONNECT 921600 % % % % @ & 26 CONNECT 307200 % % % % @ & 27 CONNECT 153600 % % % % @ & 28 CONNECT 102400 % % % % @ & 29 CONNECT 61440 % % % % @ & 30 CONNECT 51200 % % % % @ & 31 CONNECT 624000 % % % % @ & 32 CONNECT 124800 % % % % @ & 33 CONNECT 62400 % % % % @ & 34 CONNECT 41600 % % % % @ & 35 CONNECT 31200 % % % % @ $ # & 36 CONNECT 24960 % % % % @ & 37 CONNECT 20800 % % % % @ & 38 CONNECT 33600 % % % % @ $ # & 39 CONNECT 28800 % % % % @ $ # & 40 CONNECT 26400 % % % % @ $ # & 41 CONNECT 24000 % % % % @ $ # & 42 CONNECT 21600 % % % % @ $ # & 43 CONNECT 48000 % % % % @ $ # & 44 CONNECT 56000 % % % % @ $ # & 45 CONNECT 64000 % % % % @ $ # & 46 CONNECT 112000 % % % % @ $ # & 47 CONNECT 128000 % % % % @ $ # & Note: V Supported % Reporting DTE rate: CONNECT DTE_Speed @ CONNECT DTE_Speed/Protocol DCE_Speed/Error_Control [/Data_Compression] $ CONNECT DCE_Speed[/Error_Code] # CONNECT DCE_Speed/Error_Code/Protocol [/Error_Control[/Data_Compression]] & CARRIER DCE_Speed PROTOCOL: Protocol ERROR CONTROL: Error_Control [COMPRESSION: Data_Compression] CONNECT DTE_Speed * Use S42b6 to disable 'RINGING' result code Error_Code: NONE Error_Control: (This field will not show if no error control is negotiated) LAPB LAPD NONE (ATX8 only) Data_Compression: V42b DTE_Speed: all possible DTE speed supported Protocol: (only ISDN protocols are listed here) X.75 X.75M ;X.75 with MLP Bundle X.75C ;X.75 with cFos Bundle V110 V120 V120M ;V.120 with MLP Bundle V120C ;V.120 with cFos Bundle SLIP PPP BTX Use ATS35 bit 7 (ATS35.7=1) to enable the following numerical result codes when an error control connection is made. ATV0 Code ATV1 String ATV0 Code ATV1 String 50 CONNECT 61 CONNECT 24000 51 CONNECT 1200 62 CONNECT 26400 52 CONNECT 2400 63 CONNECT 28800 53 CONNECT 4800 64 CONNECT 31200 54 CONNECT 7200 65 CONNECT 33600 55 CONNECT 9600 66 CONNECT 38400 56 CONNECT 12000 67 CONNECT 48000 57 CONNECT 14400 68 CONNECT 56000 58 CONNECT 16800 69 CONNECT 64000 59 CONNECT 19200 70 CONNECT 112000 60 CONNECT 21600 71 CONNECT 128000 ------------------------------------------------------------------------------- HELP show function of keypad keys Q quit current buffer #keypad : (Num Lock) Up one line in buffer Top of Ŀ buffer --> 7 8 9 <-- Page up ͵ ͵ 2 3 <-- Page down Down one line in buffer (you can use these keys to continue) ------------------------------------------------------------------------------- QUIT